Wooden Double Entrance Doors: B2B Factory Sourcing Guide

10 min read

The first container of wooden double entrance doors leaves the factory with a specific smell — fresh PU paint mixed with the faint sweetness of kiln-dried oak. The buyer who ordered it will not see the product for another 35 days. What they worry about, in that gap, is whether the doors will arrive without warping, whether the multi-point lock aligns perfectly, and whether the U-value matches the specification sheet.

That worry is legitimate. Double doors are structurally the most demanding product a joinery factory produces. The physics are unforgiving: wider panels mean more leverage on hinges, more surface area for moisture exchange, and more perimeter for air leakage. This guide explains what separates a factory that handles those challenges well from one that ships problems.

What Are Wooden Double Entrance Doors?

Wooden double entrance doors are a pair of side-hinged door leaves, typically 1200–1800 mm total width, installed as the primary entry point of a building. Unlike single doors, they require a reinforced frame system, specific hinge engineering, and a meeting stile (the vertical joint where the two leaves close) that maintains weather sealing across the full height.

The applications are straightforward: luxury villas, boutique hotels, high-end residential developments, and commercial buildings where the entrance is part of the architectural statement. For B2B buyers, the procurement logic differs from interior doors — exterior double doors must perform structurally under wind load, thermal cycling, and forced-entry attempts, not just look good.

Quality and Performance Factors That Matter

Wood Species and Dimensional Stability

The wood species determines more than appearance. It determines whether the door stays flat in five years.

For exterior double doors, the industry uses hardwoods with proven dimensional stability:

Moisture content matters more than species. Kiln-dried wood should measure 8–12% at the time of machining. Above that, the panel will move after installation. A factory that cannot prove its moisture content readings is a factory that ships warped doors.

Anti-Sag Engineering for Wide Panels

A 900 mm single door leaf weighs roughly 35–45 kg. A double door leaf of the same height but narrower width — typically 600–800 mm per leaf — carries less weight per leaf, but the total system weight is higher. The frame must distribute that load.

Two things prevent sagging:

• 4-bar hinges or ball-bearing hinges rated for the specific leaf weight. Standard 3-knuckle hinges are insufficient for exterior double doors.
• Reinforced frame cores — LVL (laminated veneer lumber) or laminated hardwood stiles that resist torsion across the full height.

Buyers should ask suppliers for the hinge specification and frame core material in writing. If the supplier answers with “heavy-duty hinges” without a load rating, keep looking.

Sealing Systems and Thermal Performance

The meeting stile is where double doors fail. Two leaves meeting in the middle creates a vertical seam that single doors do not have. Proper sealing requires:

• Triple-seal rubber gaskets on all perimeter edges
• An overlapping or telescopic meeting stile design
• A threshold (sill) with a thermal break and drainage system

For cold climates, the U-value target should be below 1.0 W/m²K. This requires double or triple glazing with Low-E coatings and warm-edge spacer bars. A factory that offers only single-glazed options for wooden double entrance doors is not equipped for modern energy codes.

Industry Standards and Certifications

European and North American markets apply different frameworks, but the underlying tests are similar:

• EN 12207 — Air permeability (Class 4 is minimum for exterior doors; Class 8–9 for premium performance)
• EN 12208 — Water tightness (Class 7–9 for exposed locations)
• EN 12211 — Wind load resistance (Class A3–C5 depending on building height and location)
• EN 14351-1 — CE marking standard for windows and pedestrian doors
• ASTM E283 / E330 — North American equivalents for air leakage and structural performance

Fire-rated double doors (EI30, EI60, or FD30/FD60) require intumescent seals in the frame and meeting stile, plus fire-rated glazing if glass is specified. Fire rating is not simply a thicker slab — the frame, seals, and hardware all participate in the rating.

How to Evaluate Wooden Double Entrance Doors Suppliers

A Procurement Framework for B2B Buyers

When evaluating factories, use a weighted scoring system across five categories:

1. Production Capability (30%)

• Does the factory dry its own timber or buy pre-dried?
• Are CNC machining centers used for panel processing?
• What is the finishing system (UV-cured, PU spray, hand-brushed)?

2. Quality Control (25%)

• Are water-tightness and air-tightness tests done on finished units or only on samples?
• What is the inspection pass rate over the last 12 months?
• Can they provide third-party test reports?

3. Customization Flexibility (20%)

• Can they match a specific RAL color or custom grain direction?
• Can they integrate specific hardware brands (e.g., Sobinco, Hoppe, GU)?
• What is the MOQ for custom sizes vs. standard sizes?

4. Logistics and Documentation (15%)

• Do they ship FCL and LCL?
• Do they provide packing lists, proforma invoices, and certificate of origin?
• How is the door protected for sea freight (shrink-wrap, plywood crates, internal bracing)?

5. Communication and Responsiveness (10%)

• How quickly do they respond to technical questions?
• Do they send production photos at agreed checkpoints?

Questions to Ask Before Ordering

• What is the moisture content of the wood at machining time?
• What hinge model and load rating are specified for each leaf?
• Which standards do your test reports reference — EN, ASTM, or local equivalents?
• What is the U-value of the complete door system, not just the glass?
• Can you provide a production schedule with photographic checkpoints?
• What happens if doors arrive damaged — what is the claim process?
• What is your lead time for a 50-unit project with custom sizing?

Avoid Suppliers Who…

• Cannot state their moisture content range. If they say “we dry the wood properly” without a number, they are not measuring it.
• Offer single-glazed double doors as the standard option. Modern exterior doors require at least double glazing.
• Do not perform water-spray tests on finished units. The seal between the two leaves only fails under real water pressure.
• Quote delivery times under 3 weeks for custom wooden doors. Quality wood door production takes time. Fast quotes mean stock profiles or skipped drying steps.

Choose A if… Choose B if…

Choose a factory direct supplier if:

• You need 50+ units per project
• You require full customization on dimensions and finishes
• You want to eliminate middleman markup
• You need OEM or ODM support

Choose a trading company or distributor if:

• You need less than 10 units
• You require local installation and after-sales service
• You need credit terms that factories cannot offer
• You are testing the market with a sample order

The Production Process: From Raw Timber to Finished Doors

Understanding the manufacturing sequence helps buyers identify where quality is built in — or lost.

Stage 1: Timber Selection and Drying
Kiln-dried hardwood is selected to 8–12% moisture content. The drying process takes 2–4 weeks depending on species and thickness. A factory that skips this stage produces doors that will cup and twist within months.

Stage 2: Frame and Stile Machining
The frame stiles are milled from laminated or solid hardwood. For double doors, the meeting stile is machined to receive the gasket profile. CNC machining ensures consistent tolerances — critical for the meeting stile alignment.

Stage 3: Panel Construction
The door panels are constructed with a core (honeycomb, solid timber, or engineered) and veneered faces. For exterior doors, solid or laminated construction is preferred over honeycomb for security and acoustic reasons.

Stage 4: Glazing (If Specified)
Insulated glass units are fitted with warm-edge spacers. The glass is bedded in a structural sealant, and the beads are fixed. For large double doors, the glass weight can be significant — the frame must be engineered to carry it.

Stage 5: Finishing
The finishing process distinguishes premium factories. A dust-free spray booth, PU or UV-cured paint systems, and a minimum of three coats. The finish protects the wood from UV degradation and moisture ingress. A hand-brushed finish may look artisanal, but a sprayed PU finish is harder and more durable.

Stage 6: Hardware Installation
Multi-point locking systems, hinges, handles, and accessories are fitted. The lock alignment is tested — a misaligned multi-point lock is the most common field complaint for double doors.

Stage 7: Final Inspection
The finished door undergoes air-tightness, water-tightness, and wind resistance testing. Visual inspection checks for finish defects, hardware alignment, and gasket continuity.

Key Quality Indicators for Buyers

Beyond the obvious visual checks, these indicators separate a quality factory from a marginal one:

• Gasket continuity: The rubber gasket at the meeting stile must be a continuous extrusion, not a joined piece. Joints fail over time.
• Screw count: A door with 3 screws per hinge plate is under-specified. Quality hardware uses 5–6 screws per plate.
• Finish thickness: A PU finish should measure 80–120 microns. Anything less will not protect the wood in exterior conditions.
• Drainage design: The threshold and frame should have hidden drainage channels. Water must exit — not pool inside the frame.

Customization and OEM/ODM Options

For B2B buyers, customization is not a luxury — it is the standard requirement. Projects need specific sizes, specific glass configurations, and hardware that matches the building’s security specifications.

OEM (Original Equipment Manufacturing): The factory produces doors to the buyer’s exact specifications, with the buyer’s branding on the packaging. The buyer is responsible for design and specification.

ODM (Original Design Manufacturing): The factory contributes to the design based on the buyer’s requirements. This suits buyers who know their performance targets but need manufacturing input on how to achieve them.

A factory that offers both OEM and ODM, with full control over the production line, can adjust profiles and fittings to match local building codes. This matters for projects crossing borders — a door certified for Germany may not meet Australian standards without modifications.

Cost Analysis: What Drives the Price

The B2B price of wooden double entrance doors is driven by four factors:

1. Wood species — Oak and Sapele command premiums over Meranti. Accoya costs 2–3x standard hardwoods but offers exceptional stability in humid climates.

2. Glass specification — Triple glazing with Low-E coatings and argon fill adds 20–30% over double glazing. Warm-edge spacers add a smaller premium but meaningfully reduce condensation.

3. Hardware — A multi-point locking system with hook bolts costs 3–5x a single-point lock. European hardware brands (Hoppe, GU, Sobinco) carry higher prices than Asian equivalents but offer better reliability and replacement availability.

4. Finishing — UV-cured finishes in a dust-free booth cost more than hand-brushed site finishes but last longer and require no maintenance for years.

Wooden doors are not always the cheapest option. For high-humidity areas or aggressive coastal environments, buyers should prioritize moisture resistance over appearance — which may mean Accoya or engineered construction at a higher price point. The lowest quote is rarely the lowest total cost of ownership.

How We Meet These Standards at Jusen Door and Windows

The technical requirements above are not theoretical — they are the baseline we work from every day. As a factory, our approach is to meet these standards through specific engineering and process controls.

Direct Factory Supply and Full Customization

We are a direct manufacturer, which means no middleman markup between the production line and your project budget. When you request a quote, you are receiving factory pricing, not a distributor’s margin.

Our production line handles full customization on size, color, glass, and hardware accessories. If your architectural drawings specify a Sapele finish with triple glazing and a specific multi-point lock, we adjust the profile structure and fittings to match. The doors are not off-the-shelf products — they are manufactured to your drawings.

Rigorous Testing and Compliance

Every batch we ship passes pre-shipment inspection for air-tightness, water-tightness, and wind resistance — the exact standards discussed earlier. We test finished units, not just samples and prototypes.

We also understand that building codes differ by region. Our adjustable profile structure and fittings are designed to meet the local codes of your target market, whether that is CE marking for Europe, ASTM standards for North America, or the specific requirements of Australia or the Middle East.

Export Experience and Logistics

International shipping is where good doors meet bad outcomes. With our experience in foreign trade, we handle the documentation that keeps shipments moving: packing lists, proforma invoices, and full customs clearance documents.

We support both FCL and LCL shipments, with direct delivery from our China factory. Your wooden double entrance doors are packed for sea freight — internal bracing, shrink-wrap moisture barriers, and plywood crates that survive container handling.

Lead Time and Ordering

For custom wooden double entrance doors, expect 4–6 weeks lead time depending on quantity and specification. This includes timber selection, drying verification, production, finishing, and inspection. Standard sizes with no customization can ship in 2–3 weeks.

MOQ for custom production is flexible — we work with developers on large bulk orders and with importers testing the market on smaller container quantities.

If you are evaluating suppliers for a project and need detailed technical specifications, test data, or a production schedule, we are ready to discuss your drawings.

Get a Free Quote

References

[1] European Committee for Standardization. “EN 14351-1:2006+A2:2016 — Windows and doors — Product standard, performance characteristics.” CEN, 2016. https://standards.cen.eu/

[2] ASTM International. “ASTM E283-19 — Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure Differences.” ASTM, 2019. https://www.astm.org/e0283-19.html

[3] ASTM International. “ASTM E330/E330M-14 — Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference.” ASTM, 2014. https://www.astm.org/e0330_e0330m-14.html

[4] TRADA Technology. “Specifying timber for exterior joinery.” Wood Information Sheet 2.3-8. https://www.trada.co.uk/

[5] Passive House Institute. “Component Certification — Windows and Doors.” https://passivehouse.com/