Front Door with Side Glass Panels: B2B Factory Sourcing Guide

20 min read

When a contractor in Melbourne orders fifty front doors for a housing development, the conversation rarely starts with price. It starts with a drawing that specifies a 1200mm sidelight on the left side, double-glazed with Low-E coating, and a frame color matching RAL 7016. The buyer needs to know one thing: can the factory deliver that spec consistently, at scale, and on schedule?

That question sits at the center of every B2B sourcing decision for a front door with side glass panels. The product is simple to describe — an active door leaf flanked by one or two fixed glass panels — but the engineering behind it involves thermal performance, structural wind-load calculations, glass safety standards, and hardware integration. Buyers who understand these layers get better quotes, fewer field failures, and smoother installations.

This article walks through what procurement professionals need to know about sourcing front doors with sidelights from overseas manufacturers: product configurations, glass selection, supplier evaluation, cost drivers, and logistics.

Understanding Front Door with Side Glass Panels: Types and Applications

A front door with side glass panels — commonly called a door with sidelights — is an entryway system consisting of an active door leaf and one or two fixed glazed panels flanking it. The sidelights are non-operable; they exist to let natural light into the entry hall while creating a wider, more imposing entrance. Architects specify them in residential villas, boutique storefronts, and multi-family housing entrances.

Common Configurations in the Market

The configuration determines the visual balance, structural requirements, and price. Four layouts dominate the market:

Configuration	Description	Typical Use
Single door + one sidelight	Active leaf with fixed panel on left or right	Space-efficient homes, side entries
Single door + double sidelights	Active leaf centered between two fixed panels	Symmetrical facades, grand entrances
Double doors + sidelights	Two active leaves with fixed panels outside	High-end villas, commercial storefronts
Half-light vs. full-light	Door leaf partially or fully glazed	Privacy vs. light trade-off

The distinction between half-light and full-light doors matters more than most buyers expect. A half-light door has a solid lower panel — often aluminum or wood — with glazing only in the upper portion, offering privacy at eye level and below. A full-light door is entirely glazed, maximizing light transmission but requiring careful glass selection for privacy and security.

Frame Materials: What Changes with Each Option

The frame material determines structural limits, thermal performance, and maintenance requirements. Aluminum dominates the B2B market for sidelight systems for three reasons: it handles tall, heavy glass panels without flexing; it accepts thermal break polyamide strips for insulation; and it offers slim sightlines that maximize glass area.

Solid wood offers classic aesthetics but demands more maintenance and cannot match aluminum’s structural rigidity for tall sidelights. Steel provides security but performs poorly thermally without complex break designs. uPVC is budget-friendly but lacks the rigidity needed for tall panels — a 2400mm sidelight in uPVC can bow under wind load.

Why Sidelight Systems Are Structurally Different

A mullion — the vertical post separating the active door from the fixed glass panel — is the critical structural element. It transfers wind load from the glass into the frame and building structure. For tall sidelights (2600mm or higher), the mullion must be engineered for deflection limits; excessive flex causes glass stress and seal failure.

Multi-point locking systems integrate into the mullion side of the active leaf. Buyers should specify locking requirements early — a 6-point lock on a 2800mm door with sidelights is not a luxury, it is a security necessity.

B2B Takeaway: Specify the configuration — number of panels, opening direction, material, and glazing area — in the first inquiry. A vague “front door with side glass” request produces vague pricing.

Choosing the Right Glass for Front Doors: A Technical Guide

The glass specification determines safety compliance, thermal performance, acoustic insulation, and cost. It is the most complex decision in the procurement process because glass configuration has multiple layers, each serving a different function.

Safety Standards: The Non-Negotiable Baseline

Building codes in most developed markets require tempered glass for doors and sidelights. The tempering process heats glass to approximately 650°C, then rapidly cools it, creating surface compression that makes the glass four to five times stronger than annealed glass. When it breaks, it shatters into small, blunt pieces rather than dangerous shards.

Laminated glass consists of two or more glass layers bonded with a PVB (polyvinyl butyral) interlayer. When broken, the fragments adhere to the interlayer, preventing the glass from collapsing into the opening. Laminated glass provides security — it resists forced entry — and improves acoustic insulation. For sidelights at ground level, laminated glass is recommended even where codes only require tempering.

Performance Factors: U-Value, SHGC, STC, UV

Buyers specifying glass for sidelights should understand four metrics:

• U-value measures heat transfer through the glass. Double glazing (insulated glass units, or IGUs) typically achieves U-values of 2.0–2.8 W/m²K with argon filling. Triple glazing drops to 1.0–1.5 but adds weight and cost.
• Solar Heat Gain Coefficient (SHGC) measures how much solar radiation passes through. Low-E (low-emissivity) coatings reduce SHGC while allowing visible light through — critical for hot climates where summer cooling dominates.
• Sound Transmission Class (STC) rates acoustic insulation. Acoustic laminated glass with different glass thicknesses (e.g., 6mm + 6mm with a special PVB interlayer) can achieve STC ratings of 38–42, suitable for homes near busy roads.
• UV protection comes from Low-E coatings or specialized interlayers that block 99% of UV radiation, preventing interior fading.

Aesthetic and Functional Glass Types

Clear glass maximizes light but offers zero privacy. Frosted or obscured glass — produced by acid etching or sandblasting — provides privacy while transmitting diffused light. Tinted glass (gray, bronze, blue) controls solar gain and adds aesthetic depth. Decorative patterned glass creates architectural statements but can complicate cleaning.

Smart glass (switchable PDLC) is a growing premium trend. It changes from transparent to opaque with an electrical current, offering privacy on demand. For B2B buyers, smart glass adds a significant markup and requires electrical wiring — not suitable for every project.

Glass Thickness and Weight: The Hidden Cost Driver

Standard single glazing runs 5mm, 6mm, or 8mm. IGUs commonly use 5+12A+5 or 6+12A+6 configurations — the “12A” indicates the argon-filled air gap in millimeters. A 6+12A+6 IGU weighs approximately 30 kg per square meter. A 2800mm x 1000mm sidelight with such glass weighs over 80 kg.

That weight cascades through the entire assembly. Hinges must be heavy-duty. The frame profile must be deep enough to support the load. Installation requires multiple workers and specialized lifting equipment. Buyers who ignore glass weight during specification face installation delays and premature hardware failure.

B2B Takeaway: When requesting quotes, specify the full glass build: glass type, thickness, coating, and IGU configuration. A “glass front door” is not a single SKU; it is a specification sheet.

How to Evaluate Front Door with Side Glass Panels Suppliers

The supplier evaluation framework below applies to any manufacturer claiming to produce glazed entry systems. It works whether the factory is in China, Turkey, or Italy.

Manufacturing Capability: In-House vs. Assembly-Only

The critical question is vertical integration. Does the factory extrude its own aluminum profiles, or does it buy from a third-party extruder? Does it fabricate glass in-house, or does it outsource? Factories that control profile production and glass fabrication maintain tighter tolerances and better quality consistency. Assembly-only operations face supply chain variability — a delay in profile delivery from their supplier directly impacts your order.

CNC machining capability matters for precise miter cuts and hardware alignment. A factory with CNC processing centers produces consistent frame joints; a factory relying on manual cutting produces frames that look fine in a showroom but leak air and water after installation.

Quality Control and Testing Protocols

Three tests matter for glazed entry systems:

• Air permeability test measures air leakage through the closed assembly. Standards like EN 1026 classify air permeability from Class 1 (worst) to Class 4 (best). A front door with sidelights should achieve Class 3 or 4.
• Water tightness test (EN 1027) subjects the assembly to simulated wind-driven rain. Class 7A or 9A is the top rating; doors in coastal or high-rainfall areas need these ratings.
• Wind load resistance test (EN 12211) verifies the frame and glass can withstand specified wind pressures without permanent deformation. Tall sidelights in exposed locations require high wind-load classifications.

Buyers should request test reports from the factory. A manufacturer that performs these tests pre-shipment reduces on-site installation issues.

Customization Flexibility: Size, Color, Hardware

Sidelight systems are rarely standard sizes. Can the factory handle non-standard heights — 3000mm or taller? Can it produce custom widths to fit existing openings? These questions determine whether the factory can serve your project at all.

Color options depend on finishing lines. Powder coating supports any RAL color but may carry a minimum quantity. Anodized finishes offer metallic tones but are more expensive. Wood-grain foil (for aluminum frames) replicates timber aesthetics.

Hardware selection is another differentiator. Does the supplier offer branded hardware (Hoppe, Siegenia, GU) or only their own private label? For security-critical entrance doors, branded hardware with proven cycle testing (100,000+ open/close cycles) is worth the premium.

Compliance with Local Building Codes

A factory that exports globally must adapt to destination-market regulations. Cold-climate markets require thermal break profiles with polyamide strips of specific widths (typically 24mm or 34mm). Hurricane zones require impact-rated glass and reinforced frames. Egress codes mandate specific clear opening widths for the active door leaf. A factory with international experience understands these variations and adjusts its manufacturing accordingly.

B2B Takeaway: Create a Request for Quotation (RFQ) checklist that includes glass spec, frame material, dimensions, color, hardware brand, and required test certificates. Send the same checklist to multiple suppliers and compare like-for-like.

Key Quality Indicators for Front Door with Side Glass Panels Buyers

Beyond the headline features, these indicators separate reliable suppliers from problematic ones. Check them before placing a deposit.

Surface finish consistency. Anodized finishes show every imperfection. Powder coating should be uniform with no orange peel effect. Request photos of actual production pieces, not catalog images.

Hardware alignment. On a properly assembled door, handles, locks, and hinges align perfectly. Misalignment indicates poor assembly tolerances — a precursor to premature wear.

Seal quality. EPDM gaskets should fit snugly in their grooves without gaps or bunching. Poorly fitted seals cause air and water leakage, the most common field complaint for glazed entry systems.

Glass edge quality. Cut glass edges should be smooth and free of chips or cracks. A small chip in a tempered glass edge can cause spontaneous breakage weeks after installation.

Packaging adequacy. For glazed products, packaging determines transit damage rates. Wooden crates with internal bracing, glass separated by foam board, and hardware packaged separately — these details matter. Ask for packaging photos before shipment.

A reader might reasonably ask: how much can a buyer verify remotely? The honest answer is: not everything. This is why pre-shipment inspection — either by the buyer or a third-party agency — is non-negotiable for bulk orders.

Relevant Industry Standards and Certifications

Understanding the standards landscape helps buyers specify correctly and verify supplier claims.

Standard	Scope	Relevance
EN 14351-1	Performance requirements for windows and doors	CE marking for EU markets
EN 1026 / 1027	Air permeability / water tightness testing	Core performance metrics
EN 12211	Wind load resistance testing	Structural integrity
ASTM E283 / E331	Air leakage / water penetration (US)	North American equivalents
ISO 9001	Quality management systems	Factory process certification
AS 2047	Windows and doors for Australian buildings	Australia/NZ compliance

European standards (EN) and American standards (ASTM) use different testing methods, so comparing results across markets requires care. A door rated for water tightness under EN 1027 Class 7A may not carry a direct ASTM E331 equivalent. Buyers should request test reports from labs accredited for the destination market’s standards.

Production Process: From Raw Material to Finished Door

Understanding how a front door with sidelights is manufactured helps buyers ask better questions and recognize why lead times vary.

Step 1: Profile extrusion. Aluminum billets are heated to approximately 500°C and forced through steel dies to create the frame profiles. Thermal break profiles are produced by inserting polyamide strips between two aluminum chambers, then rolling the assembly to create a mechanical bond.

Step 2: Surface treatment. Profiles are either powder coated (electrostatically applied paint, cured in an oven) or anodized (electrochemical process creating a protective oxide layer). Powder coating offers more color options; anodizing offers better abrasion resistance.

Step 3: CNC machining. Profiles are cut to length, then CNC-machined for drainage holes, hardware mounting points, and corner joints. Precision at this stage determines how well the frame assembles and performs.

Step 4: Glass fabrication. Glass is cut, edge-worked, tempered or laminated, and assembled into IGUs with spacer bars and sealants. The IGU is filled with argon gas and sealed to prevent leakage.

Step 5: Frame assembly. Machined profiles are assembled into frames, gaskets are fitted, and hardware is installed. The assembled frame undergoes function testing — opening, closing, locking — before glass installation.

Step 6: Glazing and final inspection. Glass is installed into the frame with setting blocks and glazing beads. The finished door undergoes air and water testing, visual inspection, and packaging.

Step 7: Packaging and loading. Doors are packed into wooden crates with steel strapping and foam separators. Crates are loaded into containers, typically 10–15 doors per 20-foot container depending on size.

Cost Analysis: Understanding Pricing for Front Doors with Sidelights

From a B2B perspective, pricing depends on specification complexity. A basic aluminum frame with double-glazed clear glass — single door with one sidelight — typically ranges from $800 to $1,500 per unit ex-factory. Adding Low-E coating, laminated glass, custom RAL colors, or premium hardware pushes the price to $2,000–$4,000+ per unit. Bulk orders (50+ units) reduce per-unit cost through economies of scale in profile cutting and glass fabrication.

Key Cost Drivers

• Frame material: Aluminum costs more than uPVC but less than high-end solid wood.
• Glass type: Standard clear IGU is the baseline. Low-E adds 10–15%, lamination adds 15–25%, smart glass adds 100%+.
• Hardware quality: Imported European hardware (Hoppe, Siegenia) costs 2–3x domestic alternatives.
• Size and complexity: Taller sidelights and arched tops increase material waste and machining time.
• Finishes: Anodized finishes cost 20–30% more than standard powder coating.

Why Factory-Direct Pricing Matters for B2B Margins

The traditional supply chain adds layers: Factory → Trading Company → Importer → Distributor → Contractor. Each layer adds 10–20% markup. Sourcing directly from a factory eliminates these layers, allowing B2B buyers to either increase margins or undercut competitors.

A trading company might position itself as a “factory” but cannot control production quality or lead times. Ask for factory registration documents, production line photos, and a video call with the production manager. A genuine factory will oblige.

MOQs and Economies of Scale

Minimum order quantities for custom doors typically range from 10 to 50 units, depending on the factory and customization level. Custom colors (non-stock RAL) may require higher MOQs because powder coating lines need to be purged and cleaned between colors.

Mixed-container (LCL) options exist for smaller orders, but per-unit logistics costs increase. For pilot orders of 5–10 doors, LCL is practical. For ongoing projects, FCL shipments offer better economics and reduced handling damage.

B2B Takeaway: When comparing quotes, verify that the scope is identical — glass spec, hardware brand, finish, and packaging. The lowest quote is not always the cheapest if the spec differs from competitors.

Supply Chain and Logistics: Shipping from Overseas Factories

Glazed entry doors present unique logistics challenges. They are bulky, heavy, and fragile. Proper logistics planning prevents transit damage and customs delays.

FCL vs. LCL Shipping

FCL (Full Container Load) is most cost-effective for orders of 30–50 doors or more. The container is sealed at the factory, reducing handling and theft risk. LCL (Less than Container Load) suits samples and pilot orders but involves multiple handling points and longer transit times — increasing damage risk for glass products.

A 20-foot container typically holds 10–15 door sets (door + sidelights) depending on dimensions. A 40-foot container holds 25–35 sets. Buyers should work with the factory to optimize container loading — mixing door sizes to maximize space utilization reduces per-unit shipping costs.

Packaging Standards for Glass Doors

Proper packaging is the difference between a clean delivery and an insurance claim. Wooden crates with steel strapping are the standard for glazed doors. Glass surfaces are separated with foam board or cardboard. Hardware is packed separately in labeled boxes. Crates are marked with handling instructions and container loading orientation.

Buyers should request packaging photos before shipment. A factory that skimps on packaging is a factory that will blame the shipping company for damage that started at the factory.

Documentation for Smooth Customs Clearance

Export documentation must be complete and accurate. The four essential documents:

• Proforma invoice: Required for payment and pre-shipment customs.
• Packing list: Detailed dimensions and weights for each crate.
• Bill of Lading (B/L): The contract of carriage issued by the shipping line.
• Certificate of Origin: May be required for preferential tariff rates under free trade agreements.

Buyers should confirm the factory has export experience — specifically, experience shipping to their country. Customs regulations vary, and a factory that has handled dozens of shipments to the US or Australia knows the documentation requirements.

Meeting Industry Standards: How Jusen Delivers on These Procurement Requirements

Having established the technical and logistical benchmarks for sourcing front doors with sidelights, the following section outlines how one manufacturer aligns with these requirements.

As a factory specializing in aluminum entrance doors and glazed entry systems, our approach to these procurement requirements is straightforward: we meet the standards discussed above because our business depends on it. Direct factory supply means our pricing reflects production costs — not trading company markups. When buyers request a quote for a front door with side glass panels, they receive pricing based on their actual specification.

Factory-Direct Model and Price Competitiveness

Our manufacturing capability covers the full production chain: aluminum profile processing, thermal break assembly, glass fabrication, frame assembly, and final inspection. This vertical integration allows us to control quality at every stage and price competitively for bulk construction projects. Buyers work directly with the production team — not a sales intermediary — which shortens the specification-to-production cycle.

Customization and Engineering Support

Full customization is standard, not exceptional. Buyers specify size, color, glass configuration, and hardware accessories. Our adjustable profile structure and fittings are designed to match local building codes of target markets — thermal break profiles for cold climates, specific wind-load ratings for coastal zones, and egress-compliant opening widths where required.

For OEM and ODM projects, we manufacture to the buyer’s design or adapt our existing systems to their requirements. Private label branding — logo application, custom packaging — is available for distributors building their own product lines.

Quality Assurance and Export Experience

Every order undergoes pre-shipment inspection covering air-tightness, water-tightness, and wind resistance testing. These tests are performed on the actual production units, not on samples. Buyers receive test reports with their shipment documentation.

Our foreign trade experience covers FCL and LCL shipments with full export documentation: packing lists, proforma invoices, bills of lading, and certificates of origin. We handle the documentation process so buyers can focus on installation and project management.

Target Product Categories

Our production lines cover aluminum alloy entrance doors with sidelights, thermal-break aluminum doors, system windows, casement doors, sliding doors, and custom villa doors and windows. For buyers sourcing front doors with side glass panels, the aluminum entrance door line with sidelight options is the most relevant product category.

Partnership Models: How to Work with Jusen

B2B buyers engage with us through four partnership models, depending on their market position and requirements.

OEM (Original Equipment Manufacturing)

Buyers provide designs and specifications; we manufacture to their exact requirements. The buyer sells under their own brand. This model suits established distributors with existing product lines who need a reliable manufacturing partner.

ODM (Original Design Manufacturing)

We provide the design and manufacturing expertise. Buyers select from our existing door systems or request minor modifications. This model suits distributors entering the glazed door market without in-house design capabilities — they get a proven, tested product without design investment.

Private Label

We manufacture the product and apply the buyer’s brand name, logo, and packaging. This model suits importers who want a branded product without owning manufacturing or design. The buyer focuses on sales and distribution; we handle production.

Construction Project Bulk Supply

For housing developments, commercial buildings, and multi-family projects, we provide guaranteed supply capacity, consistent quality, and scheduled delivery timelines. This model suits contractors and developers who need predictable delivery for construction schedules.

Shipping and Logistics Support

Logistics are integrated into our service offering, not treated as an afterthought.

Flexible Shipping Options

We support both FCL and LCL shipments with direct delivery from our factory to the port of discharge. For FCL orders, we manage container loading to maximize space utilization and minimize damage risk. For LCL orders, we ensure robust packaging that withstands multiple handling points.

Documentation and Compliance

Full export documentation support: packing lists, proforma invoices, bills of lading, and certificates of origin. Our experience handling customs procedures for various countries means fewer delays at destination ports.

Lead Times

Typical production lead time for a standard custom order is 20–30 days after confirmation of drawings and receipt of deposit. This includes profile machining, glass fabrication, assembly, and pre-shipment inspection. Large bulk orders may require 30–45 days. Clear specifications upfront accelerate the production schedule — vague requirements lead to clarification delays.

After-Sales Support and Quality Assurance

Post-shipment support reduces the buyer’s risk and protects their reputation with end-clients.

Pre-Shipment Inspection

The air-tightness, water-tightness, and wind resistance tests performed before shipment reduce field failures and warranty claims. A door that passes these tests at the factory is unlikely to fail after installation — assuming proper installation.

Technical Support

We provide installation guidelines and technical drawings with every shipment. Remote troubleshooting support is available for installation teams encountering issues. Most installation questions are resolved with a video call.

Warranty Policy

Aluminum profiles carry a 5–10 year warranty against manufacturing defects. Hardware carries a 2–3 year warranty. Warranty claims are handled based on inspection and root-cause analysis — if the failure stems from improper installation or external factors, the warranty does not apply.

Client Applications: Where Our Doors Are Used

Residential Villas and Custom Homes

Custom sidelights create grand entryways for high-end residential projects. The current trend favors black aluminum frames with clear glass for modern minimalist architecture. Buyers specify double sidelights for symmetrical facades, often with smart glass for privacy control.

Commercial Projects

Boutique storefronts, offices, and hotels use glazed entry systems for their durability and low maintenance. Aluminum frames withstand high-traffic usage without the maintenance demands of timber. Thermal break profiles maintain comfortable interior temperatures near large glazed areas.

Multi-Family Housing

Apartment buildings and condominium complexes use front doors with sidelights for common entryways and individual units. Cost-effectiveness matters at this scale, as does compliance with local fire and egress codes. Bulk supply arrangements ensure consistent quality across hundreds of units.

Frequently Asked Questions

What is a glass door in front of a front door called?

A full glass door placed outside the main door is called a storm door. The glass panels flanking the active door leaf are called sidelights. This article focuses on sidelights — fixed glass panels installed beside the active door, either on one side or both sides.

How much does a glass front door cost?

From a B2B perspective, a basic aluminum frame with double-glazed clear glass — single door with one sidelight — ranges from $800 to $1,500 per unit ex-factory. Adding Low-E coatings, laminated glass, custom colors, or premium hardware increases the price to $2,000–$4,000+ per unit. Bulk orders reduce per-unit cost.

Is it okay to have a glass front door?

Yes, provided the correct glass is used. Building codes require tempered or laminated glass for doors and sidelights to prevent injury. For energy efficiency, use double glazing with a Low-E coating. For security, laminated glass is recommended — it resists forced entry because the PVB interlayer holds the glass together when broken.

What is the difference between a single door with sidelights and a double door?

A single door with sidelights has one active door leaf with one or two fixed glass panels beside it. A double door has two active leaves. Sidelights achieve a wide, grand entrance without the cost and space requirements of a double door — the active opening remains narrower, which also reduces heat loss.

What is the lead time for a custom order of front doors with sidelights?

Typical production lead time is 20–30 days after confirmation of drawings and receipt of deposit. This includes profile machining, glass fabrication, assembly, and pre-shipment inspection. Large bulk orders may require 30–45 days. Shipping time adds 20–40 days depending on destination.

Can you match specific RAL colors for the aluminum frames?

Yes. We support full powder coating in a wide range of RAL colors. Standard colors (Black, White, Grey) have faster lead times. Custom RAL colors may have a minimum quantity requirement because powder coating lines need to be purged between color changes.

Choosing the Right Supplier: A Decision Guide

Choose a direct factory if your order volume justifies container shipping (30+ doors) and you have the capacity to manage overseas logistics. The cost savings of 20–30% versus trading company pricing directly improves your margin.

Choose a trading company if you need a single supplier for multiple product categories (doors, windows, hardware) that no single factory produces. Trading companies aggregate across factories but add markup.

Choose an OEM/ODM partnership if you need custom designs, private labeling, or a branded product line. This requires a factory with engineering capability and flexible production.

Choose a bulk supply arrangement if you are a contractor or developer with ongoing project demand. Long-term relationships secure capacity and pricing stability.

—

Ready to source front doors with side glass panels for your next project? As a manufacturer with deep experience in foreign trade and bulk supply, we are ready to discuss your specifications. Contact our team today for a detailed quote and project consultation.

Get a Free Quote

—

References

• European Committee for Standardization. “EN 14351-1:2006+A2:2016 — Windows and doors — Product standard, performance characteristics.” https://www.en-standard.eu/
• European Committee for Standardization. “EN 1026:2016 — Windows and doors — Air permeability — Test method.” https://www.en-standard.eu/
• European Committee for Standardization. “EN 1027:2016 — Windows and doors — Water tightness — Test method.” https://www.en-standard.eu/
• European Committee for Standardization. “EN 12211:2016 — Windows and doors — Resistance to wind load — Test method.” https://www.en-standard.eu/
• ASTM International. “ASTM E283-19 — Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Skylights, and Doors.” https://www.astm.org/
• ASTM International. “ASTM E331-00(2023) — Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference.” https://www.astm.org/
• Standards Australia. “AS 2047:2014 — Windows and doors — Installation.” https://www.standards.org.au/
• International Organization for Standardization. “ISO 9001:2015 — Quality management systems — Requirements.” https://www.iso.org/